(1) oil spill in the main air compressor accessories products, materials or workmanship poor structural design problems; improper assembly process, such as mating surfaces dirty air compressor manufacturers supply, liner damaged or displaced; fastening Tighten the nut is uneven or Songkuang force as a result of mechanical work off failure; after long-term use of the sealing material wear off limits, aging metamorphism, deformation failure; lubricating oil to add too much or inconsistent; Compressor Parts binding surface deflection deformed, broken air compressor manufacturer, wholesale shell, so that oil leaking; breather after a one-way valve plug, due to the pressure difference inside and outside the enclosure of the role of the oil spill caused by the weak seal. The main method (2) management of oil spills ① installation gasket correctly. Gasket between the air compressor parts function plays a leakproof seal, if material, production and installation of the upper and lower quality does not meet the technical specifications, can cause leakage. ② properly tightened nut. Pressure is not too loose will cause the liner and leak tight, too tight will make the metal bumps around the screw, or threaded twist slip and cause leakage. ③ timely replacement seal failure. Many parts of the compressor seals due to improper installation, resulting in a different journal and seal edge heart and dumped oil. Some seals due to aging and loss of elasticity of the rubber used for a long time after. ④ timely replacement of worn parts. Air compressor parts (such as the piston and cylinder) will have long used excessive wear limit, resulting in the combustion chamber of high pressure gas into the crankcase, forcing oil leakage. ⑤ avoid a one-way valve, vent valve blocked. If the check valve, the vent valve closed, will cause the temperature rise within the housing, and gas fills the entire space, so that increased pressure within the housing, and increased resistance to movement of the piston, so that fuel consumption increases, and because the case housing the inner and outer the role of pressure difference, often lead to weak seal leakage. 1, the air output temperature is too high (1) to reduce the input screw air compressor air temperature. Increase air compressor room ventilation in the room plus roof exhaust hood, used to exclude heat, control room temperature is not too high. Summer air compressor manufacturer, air compressor room temperature should not exceed 40 ℃. (2) reduce the cooling water inlet temperature, winter water temperature maintained at 18 ℃, summer water temperature maintained at 24 ℃. (3) increase the flow of cooling water, the estimated temperature of the cooling water input and output of the temperature difference between l5 ℃, the cooling water flow rate of 3.7 liters / sec. (4) removal of the cooling water scale or dirty sediment. In the cooling water by adding detergent to clear cooling water system. 2, high oil temperature screw compressor screw compressor oil temperature protection settings, oil temperature exceeds 70 ℃, shut down, resulting in frequent compressor shutdown. Oil temperature is too high because the oil cooler failure. Since the cooling water circuit in the oil cooler is fine, easy to clean up after fouling, resulting in the oil temperature does not drop down. Replacing an oil cooler and too expensive. After the study explored using the following methods to clean the cooler is better. Remove the oil cooler, soaked in detergent in one day, and then a small pump water under pressure into the oil cooler repeated washing, the scale can be removed in summer to control the oil temperature below 60 ℃. 3, the air filter frequently fail to start using screw air compressor, the air filter is only one month on the failure. The analysis of ambient air is dirtier. For this reason above plus access cover on the air compressor air filter, longer filter life. 4, screw air compressor screw air compressor motor burned frequently during use, the main motor frequently burned over a period of time. The main reason is that no one thing has its maximum operating pressure, and over the working pressure and long-running, long-term overload, it will cause the compressor motor overheating, burning motor. Air compressor manufacturer price _ _ Air Qin Wei Baoji, Xianyang compressor manufacturer provided by Compressor Co., Ltd. Qin Wei. Xianyang Qin Wei Compressor Co. (www.xykyj.cn/) is Xianyang, compression, separation equipment leader, over the years, the company implementing the scientific management, innovation and development, the principle of honesty and trustworthiness, and satisfy customer needs. Qin Wei Air leadership with the staff warmly welcome all inquiries negotiations to create Qin Wei Air a better future.