In addition to water, compressed air is a no-filter, no electricity, free labor to maintain air moisture removal device, which is one of the compressor assembly equipment. Compressed air generated by the compressor is not pure. This is because the air compressor itself contains lubricating oil, during the compression work, there must be part of the lubricating oil mixed into the air to go. Also the nature of air itself contains a number of solid particles and water, etc., when using this without purification of gas compressor manufacturers directly in the pneumatic circuit, pneumatic circuit will bring some failures, damage pneumatic components, reducing component use life, productivity decline, or even cause an accident. Compressed air eliminators, you can make the pipeline when the air cools down, it began to produce condensed liquid flows along the pipeline. Once the air flowing into the filter drier / filter, it will produce a series of phenomena. First, the coagulation effect, condenser or the first stage filter (stainless steel mesh) to promote water and air to change direction. This change makes the individual droplets combine with each other and then gathered in the condensed Lane. Drop gradually become larger, combined with other larger contaminants into the role of gravity in the downstream storage room - central area. Water containing dirt and rule out along the bottom of the flow through the automatic drain valve draining the pool; lots of water (an estimated 95% of water) is discharged through this process. The second filtration process through the second filter element cotton web. Change in the direction of the cotton fiber rope in or near airflow and airflow Cottle rotary compressor manufacturers, the cotton fiber rope is supported by a stainless steel mesh, forming a whirlpool, a few times when the air is accelerated, the vortex center As the tornado, a vacuum state. Therefore, the first air-dried filters filter the water droplets not removed in this pair is gasified gas compressor no adverse effects, but also tiny droplets of this impurity is removed. Cleaning offloading valve (inlet valve) unloader valve manifold from the valve body, valve (piston), pneumatic, solenoid valve and proportional valve (capacity control valve) and other components. Unloader valve is mainly controlled compressor load (screw compressor heavy vehicles), unloading (empty), the proportion of (capacity control) control action, in addition to prevent the compressor shut down when the lubricating oil discharged from the host. (1) The unloader valve disassembly: ① unloader valve hose to remove the air filter connected; ② remove all other components and offloading valve connected to the trachea; ③ demolition solenoid coil; ④ demolition offload valve assembly with the host nut and remove; ⑤ the valve moves to offload lined with clean paper or a clean skin surface. (2) Cleaning unloader valve: Cleaning agents should use soap and water, diesel fuel, clean gasoline, and other days of the receiving water, the cleaning agent can be used depending on the degree of dirt, it is generally recommended to use soap and water or diesel fuel for cleaning. (3) Remove the solenoid valve: Remove the solenoid valve and check whether the O-rings and sealing sheet solenoid valve needs to be replaced (Tip: If you are unfamiliar intake valves, please note the location of the element removed, so when you replace Error). Such as the need to replace the removed screws, O-rings, the sealing sheet, the solenoid rod, batteries and other components into a prepared container, and placed in a suitable cleaning agent soak (Note: in the selection of petrol and days of receiving water for cleansing When the agent, do not rubber O-rings soaked for too long, in order to avoid corrosion); (4) Remove the proportional valve: the proportional valve is removed from the body, and then tighten the adjusting nut (preferably before screwing on the nut do some mark, so the proportion of the value of the deviation is too large when you replace it), remove the valve core, O-rings, U-rings, springs and check O, whether the U-rings need to be replaced (removed all seals and springs are required to do The checks described below will not be repeated in the instructions), the removed element soaked in a cleaning agent. (5) Remove manifold Manifold: The manifold is removed from the valve body, the four sides of the manifold have stomata (screw compressor of the hole play a clear role in the integrated air passage blockage) famous Compressor Manufacturers, on the packing nut is screwed off and the vent manifold together into the cleaning agent soak. (6) Remove the unloader valve body: with snap ring pliers to remove the spool retainer and valve body is located at the junction, and then unscrew the spool pipe wrench, remove the inside of the cylinder, valves, O-rings, U ring, spring and soaked in a cleaning agent, and then split the air inlet valve on the compressor manufacturers supply the entire body soak, this time, the unloader valve disassembly process has been completed. Compressor manufacturers ranking, Chengdu compressor manufacturers, Qin Wei Qin Wei Pneumatic provided by Compressor Co., Ltd. Xianyang. Xianyang Qin Wei Compressor Co. (www.xykyj.cn/) strong, credible, Xianyang in Shaanxi compression, separation equipment industry has accumulated a large number of loyal customers. The company better work attitude and constantly improving innovative ideas will lead Qinwei Air into the brilliant and you work for a better future!